U23 2008-2/Gruppe1
Meta Data
Mitglieder
- Mark<br />
- Christoph<br />
- Hendrik<br />
- Robert<br />
Code
1. Abend
LED - Blinken
- Aufgabe: Eine LED soll zum blinken gebracht werden.
- Code:
<source lang ="c"> //**************************************************************************** // * // * Von Gruppe 1 // * Aufgabe: Alle LEDs sollen zum blinken gebracht werden. // * // * Task: All LED shall blink. // * //****************************************************************************
- include <avr/io.h>
- include <util/delay.h>
int main(void) { /* LED Anschluss */ /* LED output */ /* LED1 PC4 */ /* LED2 PD3 */ /* LED3 PD6 */ /* LED4 PD7 */
/* Setze Ports PC4, PD3, PD6 und PD7 als Ausgang */
/* Set ports PC4, PD3, PD6 and PD7 as outputs */
DDRC = _BV(4);
DDRD = _BV(7)|_BV(6)|_BV(3);
while(1) {
/* _delay_ms() verzögert um 10 Millisekunden */ /* 50 * 10ms = 500ms */ /* _delay_ms() delays for 10 Milliseconds */ /* 50 * 10ms = 500ms */ for (uint8_t i=0;i<50;i++) _delay_ms(10);
/* Schalte zwischen 5V und 0V an den Ausgängen hin und her */ /* Toggle 5V and 0V at the outputs */ PORTC ^= _BV(4); PORTD ^= _BV(7)|_BV(6)|_BV(3);
} return 0; }
</source>
<br />
LED - Einschalten
- Aufgabe: Eine LED soll zum leuchten gebracht werden.
- Code:
<source lang ="c"> //**************************************************************************** // * // * Von Gruppe 1 // * Aufgabe: Eine LED soll zum leuchten gebracht werden. // * //****************************************************************************
- include <avr/io.h>
int main(void) {
/* PC4 auf Ausgang */ DDRC = &b10000; /* Alternativ Hex: 0xF oder Dezimal: 16 */ /* 7 6 5 4 3 2 1 0 */ /* 0 0 0 1 0 0 0 0 */
/* PC4 einschalten */ PORTD = &b10000;
/* Endlosschleife */
while(1)
{
}
}
</source>
LED - Lauflicht
- Code:
<source lang ="c"> //**************************************************************************** // * // * Von Gruppe 1 // * //****************************************************************************
- include <avr/io.h>
- include <util/delay.h>
int main(void) { unsigned int i;
/* Setze Ports PC4, PD3, PD6 und PD7 als Ausgang */ DDRC = (1<<DDC4); DDRD = (1<<DDD7)|(1<<DDD6)|(1<<DDD3); /* Setze Ports PC4, PD3, PD6 und PD7 auf low */ PORTC = (0<<PC4); PORTD = (0<<PD7)|(0<<PD6)|(0<<PD3);
while(1) {
PORTC ^= _BV(PC4); for (i=0;i<50;i++) _delay_loop_2(0); PORTC ^= _BV(PC4); PORTD ^= _BV(PD3); for (i=0;i<50;i++) _delay_loop_2(0); PORTD ^= _BV(PD3); PORTD ^= _BV(PD6); for (i=0;i<50;i++) _delay_loop_2(0); PORTD ^= _BV(PD6); PORTD ^= _BV(PD7); for (i=0;i<50;i++) _delay_loop_2(0); PORTD ^= _BV(PD7);
} return 0; } </source>
Blinksequenz aufzeichnen und später abspielen
<source lang="c">#include <avr/io.h>
- include <util/delay.h>
- define SEQS 100
typedef struct { uint8_t bstate; uint32_t dur; } seq_t;
seq_t seq[SEQS]; uint8_t count = 0;
void wait(uint32_t ms); void record(void); void play(void);
void wait(uint32_t ms) {
uint32_t i;
for (i = 0; i < ms; i++) { _delay_ms(1); } }
void record(void) {
uint32_t dur = 0; uint8_t bstate_prev = 0x00; // prev button state uint8_t bstate = 0x00; // current button state
while (1) { bstate = 0x00;
// S1 if (~PINC & _BV(PC0)) { bstate |= 1 << 1; }
// S2 if (~PINC & _BV(PC1)) { bstate |= 1 << 2; }
// S3 if (~PINC & _BV(PC2)) { bstate |= 1 << 3; }
// S4 if (~PINC & _BV(PC3)) { bstate |= 1 << 4; }
// omit first state if (count == 0 && bstate == 0x0) { continue; }
if (count >= SEQS) { // overflow error => all LEDs on while (1) { PORTC |= _BV(PC4); PORTD |= _BV(PD3) | _BV(PD6) | _BV(PD7); } }
if (bstate_prev == bstate) { if (dur + 50 > dur) { dur += 50; }
if (bstate == 0x0 && count > 0 && dur >= 2000) { // no button was pressed for 2s return; } } else { // save state seq[count].bstate = bstate_prev; seq[count].dur = dur; count++;
// prepare for next state dur = 0; bstate_prev = bstate; }
wait(50); } }
void play(void) { uint8_t i;
while (1) { // PORTD |= _BV(PD7);
for (i = 0; i < count; i++) { // LED1 if (seq[i].bstate & 1 << 1) { PORTC |= _BV(PC4); } else { PORTC &= ~_BV(PC4); }
// LED2 if (seq[i].bstate & 1 << 2) { PORTD |= _BV(PD3); } else { PORTD &= ~_BV(PD3); }
// LED3 if (seq[i].bstate & 1 << 3) { PORTD |= _BV(PD6); } else { PORTD &= ~_BV(PD6); }
// LED4 if (seq[i].bstate & 1 << 4) { PORTD |= _BV(PD7); } else { PORTD &= ~_BV(PD7); }
wait(seq[i].dur); }
PORTC &= ~_BV(PC4); PORTD &= ~_BV(PD3) & ~_BV(PD6) & ~_BV(PD7); wait(300);
} }
int main(void) {
DDRC |= _BV(PC4);
DDRD |= _BV(PD3) | _BV(PD6) | _BV(PD7); // all LEDs are output
DDRC &= ~_BV(PC0) & ~_BV(PC1) & ~_BV(PC2) & ~_BV(PC3); // S[1..4] are input PORTC |= _BV(PC0) | _BV(PC1) | _BV(PC2) | _BV(PC3); // use pullup for S[1..4]
// wait for pullops to "settle down" wait(1000);
while (1) { record(); play(); } }</source>
2. Abend
Änderungen des IR-Signals werden aufgezeichnet, und auch zeitlich ausgewertet. Messung ist jedoch relativ ungenau. Implementation von Timer / Counter fehlt.
<source lang ="c"> /* ################################### */ /* # IR-Empfang # */ /* # Von Gruppe 1 # */ /* ################################### */ /* # Done: IR-Signale chronologisch # */ /* # aufzeichnen # */ /* ################################### */ /* # Todo: Counter / Timer einbauen # */ /* ################################### */
- include <avr/io.h>
- include <string.h>
- include <stdio.h>
- include <avr/pgmspace.h>
- include <util/delay.h>
- include "uart.h"
int main(void) { int status = 0; int counter = 0;
/* initialize serial uart */ uart_init();
/* configure irrx as input */ DDRC &= ~_BV(PC3);
/* init led pin as output */ DDRD |= _BV(PD3);
while(1) {
counter++;
for (int i = 0; i<10; i++)
{
_delay_us(10);
}
/* if ir rx is high, turn off led */
if (PINC & _BV(PC3)) {
// Kein IR
PORTD &= ~_BV(PD3);
if (status == 1)
{
uart_printf("Ir jetzt aus %u\n",counter);
counter = 0;
}
status = 0;
} else {
PORTD |= _BV(PD3);
if (status == 0)
{
uart_printf("Ir jetzt an %u\n",counter);
counter = 0;
}
status = 1;
}
}
} </source>
3. Abend
IR-Jammer
Sendet, sobald er IR empfängt, für 1000ms und wartet dann 5ms, damit er das ausgesandte Signal nicht wieder empfängt.
<source lang="c">
- include <avr/io.h>
- include <avr/interrupt.h>
- include <util/delay.h>
- include "uart.h"
/* constants */
- define MAX 160
/* 38khz: freq = F_CPU/(2*prescaler*frequency)
* 20mhz/(2*8*38khz) = ~33 * real frequency: 20mhz/(2*8*33) = ~37878Hz */
- define PWM_FREQ 33
/* global variables */
/* allocate 160*2 = 320 byte memory for storing a code,
* this means we can store 80 on/off sequence timings */
volatile uint16_t code[MAX]; /* current index in code[] (default: 0) */ volatile uint8_t pos = 0; /* current pin state (default: high == idle) */ volatile uint8_t state = 1; /* signal for the main application that a code has been received
* (default: 0) */
volatile uint8_t done = 0; /* signal button presses from interrupt to main */ volatile uint8_t button_press; /* current system mode */ enum {
MODE_OFF = 0, MODE_DISPLAY = 1, MODE_JAM = 2, MODE_RECORD = 3,
} mode = MODE_DISPLAY; /* current viewmode */ enum {
VIEW_VALUE_AND_TIME = 0, VIEW_VALUE = 1, VIEW_TIME = 2,
} view = VIEW_VALUE_AND_TIME;
/* call every 10 ms, for buttons at pins PC0-PC3 */ static uint8_t button_sample(void) {
/* initialize state, buttons are active low! */ static uint8_t btn_state = 15; //0b1111; /* initialize old sample */ static uint8_t last_sample = 15; //0b1111; /* read inputs */ uint8_t new_sample = PINC & 15; //0b1111;
/* mark bits which are sampled with the same value */
uint8_t same_sample = (last_sample ^ ~new_sample);
/* all bits set in same_sample now have been sampled with the same value
* at least two times, which means the button has settled */
/* compare the current button state with the most recent sampled value,
* but only for those bits which have stayed the same */
uint8_t state_different = btn_state ^ (new_sample & same_sample);
/* all bits set in state_different have been sampled at least two times
* with the same value, and this value is different from the current
* button state */
/* if a bit is set in state (means: button is not pressed) AND bit is set
* in state_different (means: input has settled and value is different
* from state) together means: button has been pressed recently */
uint8_t btn_press = btn_state & state_different;
/* toggle all bits for inputs which switched state */ btn_state ^= state_different;
/* store current sample for next time */ last_sample = new_sample;
/* if bit is set in btn_press, a button has been pressed
* (not released yet) */
return btn_press;
}
void wait(uint32_t s) { uint32_t i; for (i = 0; i < s; i++) { _delay_ms(1); } }
/* set up timer 0 to generate a carrier using pwm at freq on pin OC0B (PD5) */ static void ir_enable(uint8_t freq) {
/* timer 0: fast pwm mode, clear OC0B on match, prescaler 8 */ TCCR0A = _BV(WGM00) | _BV(COM0B1); TCCR0B = _BV(CS01) | _BV(WGM02);
/* set frequency */ OCR0A = freq;
/* set duty-cycle to 50% */ OCR0B = freq/2;
}
/* disable timer 0 and pwm generation */ static void ir_disable(void) {
TCCR0A = 0; TCCR0B = 0;
}
/* pin change interrupt 1 service function */
ISR(PCINT1_vect)
{
/* do nothing if we are just processing a code in the main loop,
* or no more space is available for a timer value */
if (done || pos == MAX)
return;
/* if this would be the first timing value ever recorded, and the
* state before was high (=idle), do not record the timing value
* and just reset the timer */
if (state && pos == 0) {
TCNT1 = 0;
/* else record the timing value */
} else {
/* store current timer value in code[]
* and reset the timer */
code[pos++] = TCNT1;
TCNT1 = 0;
}
/* toggle second led */ PORTD ^= _BV(PD3);
/* toggle state */ state = !state;
}
/* timer 1 compare A interrupt service function */ ISR(TIMER1_COMPA_vect) {
/* do nothing if we are just processing a code in the main loop */
if (done)
return;
/* if some code has been received */
if (pos > 0) {
/* if pos is odd, one last 'off'-timing is missing, fill with zero */
if (pos % 2 == 1)
code[pos++] = 0;
/* signal main */
done = 1;
/* turn on third led */
PORTD |= _BV(PD6);
}
}
/* timer 2 compare A interrupt service function */ ISR(TIMER2_COMPA_vect) {
/* sample buttons every 10ms */ button_press |= button_sample();
}
int main(void) {
/* initialize uart */
uart_init();
uart_printf("rumpus ir analyzer\n");
/* configure led pins as outputs and turn leds off */ DDRC |= _BV(PC4); DDRD |= _BV(PD3) | _BV(PD6) | _BV(PD7); PORTC &= ~_BV(PC4); PORTD &= ~(_BV(PD3) | _BV(PD6) | _BV(PD7));
/* configure ir input pin, with pullup */ DDRC &= ~_BV(PC3); PORTC |= _BV(PC3);
/* configure button input pins, with pullup */ DDRC &= ~(_BV(PC0) | _BV(PC1) | _BV(PC2) | _BV(PC3)); PORTC |= _BV(PC0) | _BV(PC1) | _BV(PC2) | _BV(PC3);
/* configure ir send pin as output, set low */ DDRD |= _BV(PD5); PORTD &= ~_BV(PD5);
/* wait until pin is high (no ir carrier is detected) */ while(!(PINC & _BV(PC3)));
/* enable pin change interrupt 1 for ir input pin (PC3/PCINT11) */ PCMSK1 |= _BV(PCINT11); PCICR |= _BV(PCIE1);
/* configure timer1 with prescaler 64 and CTC for measuring ir timings */ TCCR1B = _BV(CS11) | _BV(CS10) | _BV(WGM12); /* configure timer action after 200ms: 20mhz/64/5 */ OCR1A = F_CPU/5/64; /* enable OCR1A interrupt */ TIMSK1 = _BV(OCIE1A);
/* configure timer 2 with prescaler 1024 and CTC
* for button sampling */
TCCR2A = _BV(WGM21);
TCCR2B = _BV(CS22) | _BV(CS21) | _BV(CS20);
/* configure compare event a to occur after 10ms and enable interrupt */
OCR2A = F_CPU/1024/100;
TIMSK2 = _BV(OCIE2A);
/* signal user availability by turning on led 1 */ PORTC |= _BV(PC4);
/* enable interrupts */ sei();
/* signal the user that the analyzer part has started by turning led 1 on */ PORTC |= _BV(PC3);
while(1) {
/* if a code has been received */
if (mode == MODE_DISPLAY && done) {
/* print code to serial uart */
uart_printf("complete code received, %u on-off-timings:\n", pos/2);
for (uint8_t i = 0; i < pos; i += 2) {
if (view == VIEW_VALUE_AND_TIME) {
uint32_t on, off;
/* compute timing in microseconds */
on = ((uint32_t)code[i]) * 64 / 20;
off = ((uint32_t)code[i+1]) * 64 / 20;
uart_printf(" %5lu us (%5u) on, %5lu us (%5u) off\n",
on, code[i],
off, code[i+1]);
} else if (view == VIEW_VALUE) {
uart_printf(" %5u on, %5u off\n",
code[i], code[i+1]);
} else if (view == VIEW_TIME) {
uint32_t on, off;
/* compute timing in microseconds */
on = ((uint32_t)code[i]) * 64 / 20;
off = ((uint32_t)code[i+1]) * 64 / 20;
uart_printf(" %5lu us on, %5lu us off\n",
on, off);
}
}
/* turn off second and third led */
PORTD &= ~(_BV(PD3) | _BV(PD6));
/* wait until pin is high (no ir carrier is detected) */
while(!(PINC & _BV(PC3)));
/* reset all global variables */
pos = 0;
state = 1;
done = 0;
}
if (mode == MODE_JAM) { // hier wird gejammt!
if (!state) { DDRC |= _BV(PC3); // ir empfang aus
ir_enable(PWM_FREQ); wait(1000); ir_disable();
wait(5); // damit wir unser eben gesendetes signal nicht empfangen DDRC &= ~_BV(PC3); // ir empfang an
done = 0; pos = 0; } }
if (button_press) {
/* first button toggles system mode */
if (button_press & 1) {
mode++;
if (mode > MODE_RECORD)
mode = MODE_OFF;
if (mode == MODE_OFF) {
uart_printf("ir analyzer switched off\n");
/* disable timer1 and pin change interrupts */
TIMSK1 &= ~_BV(OCIE1A);
PCMSK1 &= ~_BV(PCINT11);
/* turn off led1 */
PORTC &= ~_BV(PC4);
} else if (mode == MODE_DISPLAY) {
uart_printf("scan and display codes\n");
/* clear interrupt flags, enable timer1 and pin change interrupts */
TIFR1 = _BV(OCIE1A);
TIMSK1 |= _BV(OCIE1A);
PCMSK1 |= _BV(PCINT11);
/* turn on led1 */
PORTC |= _BV(PC4);
} else if (mode == MODE_JAM) {
/* clear interrupt flags, enable timer1 and pin change interrupts */
TIFR1 = _BV(OCIE1A);
TIMSK1 |= _BV(OCIE1A);
PCMSK1 |= _BV(PCINT11);
uart_printf("jamming mode active\n");
} else if (mode == MODE_RECORD) {
uart_printf("record and replay a code\n");
}
}
/* second button toggles view mode */
if (button_press & 2) {
view++;
if (view > VIEW_TIME)
view = VIEW_VALUE_AND_TIME;
if (view == VIEW_VALUE_AND_TIME)
uart_printf("display timer value and time (in us)\n");
else if (view == VIEW_VALUE)
uart_printf("display timer value\n");
else if (view == VIEW_TIME)
uart_printf("display time (in us)\n");
}
if (button_press & 4) {
static uint8_t pwm = 0;
if (!pwm) {
ir_enable(PWM_FREQ);
uart_printf("pwm on\n");
} else {
ir_disable();
uart_printf("pwm off\n");
}
pwm = !pwm;
}
button_press = 0;
}
}
}</source>
4. Abend
IR-Jammer in schlau
Misst die kürzeste Impulsdauer und sendet mit dieser (plus einer kleinen, sich ändernden Verzögerung) in die Pausen.
<source lang="c">#include <avr/io.h>
- include <avr/interrupt.h>
- include <util/delay.h>
- include "uart.h"
/* constants */
- define MAX 160
/* 38khz: freq = F_CPU/(2*prescaler*frequency)
* 20mhz/(2*8*38khz) = ~33 * real frequency: 20mhz/(2*8*33) = ~37878Hz */
- define PWM_FREQ 33
/* global variables */
/* allocate 160*2 = 320 byte memory for storing a code,
* this means we can store 80 on/off sequence timings */
volatile uint16_t code[MAX]; /* current index in code[] (default: 0) */ volatile uint8_t pos = 0; /* current pin state (default: high == idle) */ volatile uint8_t state = 1; /* signal for the main application that a code has been received
* (default: 0) */
volatile uint8_t done = 0; /* signal button presses from interrupt to main */ volatile uint8_t button_press; /* current system mode */ enum {
MODE_OFF = 0, MODE_DISPLAY = 1, MODE_JAM = 2, MODE_RECORD = 3,
} mode = MODE_DISPLAY; /* current viewmode */ enum {
VIEW_VALUE_AND_TIME = 0, VIEW_VALUE = 1, VIEW_TIME = 2,
} view = VIEW_VALUE_AND_TIME;
/* call every 10 ms, for buttons at pins PC0-PC3 */ static uint8_t button_sample(void) {
/* initialize state, buttons are active low! */ static uint8_t btn_state = 15; //0b1111; /* initialize old sample */ static uint8_t last_sample = 15; //0b1111; /* read inputs */ uint8_t new_sample = PINC & 15; //0b1111;
/* mark bits which are sampled with the same value */
uint8_t same_sample = (last_sample ^ ~new_sample);
/* all bits set in same_sample now have been sampled with the same value
* at least two times, which means the button has settled */
/* compare the current button state with the most recent sampled value,
* but only for those bits which have stayed the same */
uint8_t state_different = btn_state ^ (new_sample & same_sample);
/* all bits set in state_different have been sampled at least two times
* with the same value, and this value is different from the current
* button state */
/* if a bit is set in state (means: button is not pressed) AND bit is set
* in state_different (means: input has settled and value is different
* from state) together means: button has been pressed recently */
uint8_t btn_press = btn_state & state_different;
/* toggle all bits for inputs which switched state */ btn_state ^= state_different;
/* store current sample for next time */ last_sample = new_sample;
/* if bit is set in btn_press, a button has been pressed
* (not released yet) */
return btn_press;
}
static void wait(uint32_t s) { uint32_t i; for (i = 0; i < s; i++) { _delay_us(1); } }
/* set up timer 0 to generate a carrier using pwm at freq on pin OC0B (PD5) */ static void ir_enable(uint8_t freq) {
/* timer 0: fast pwm mode, clear OC0B on match, prescaler 8 */ TCCR0A = _BV(WGM00) | _BV(COM0B1); TCCR0B = _BV(CS01) | _BV(WGM02);
/* set frequency */ OCR0A = freq;
/* set duty-cycle to 50% */ OCR0B = freq/2;
}
/* disable timer 0 and pwm generation */ static void ir_disable(void) {
TCCR0A = 0; TCCR0B = 0;
}
static void jam(void) { static uint32_t dur; static uint16_t i; uint8_t j = 0; uint32_t dur_tmp;
if (pos == 0 || done) { dur = 0xFFFFFFFF; }
if (i % 500 == 0) { i=0; if (!state) { uart_printf("-"); } else { uart_printf("."); } } i++;
if (pos < 1) {
return;
}
// shortest measured duration dur_tmp = ((uint32_t)code[pos-1]) * 64 / 20; dur = dur_tmp < dur ? dur_tmp : dur;
while (!state && j < 10) { j++; DDRC |= _BV(PC3); // ir reciever off
ir_enable(PWM_FREQ); uart_printf("*"); wait(dur+i); ir_disable();
wait(250); // we don't want to recieve our own signal (due to lags in the ir receiver) DDRC &= ~_BV(PC3); // ir reciever on } }
/* pin change interrupt 1 service function */ ISR(PCINT1_vect) {
/* do nothing if we are just processing a code in the main loop,
* or no more space is available for a timer value */
if (done || pos == MAX)
return;
/* if this would be the first timing value ever recorded, and the
* state before was high (=idle), do not record the timing value
* and just reset the timer */
if (state && pos == 0) {
TCNT1 = 0;
/* else record the timing value */
} else {
/* store current timer value in code[]
* and reset the timer */
code[pos++] = TCNT1;
TCNT1 = 0;
}
/* toggle second led */ PORTD ^= _BV(PD3);
/* toggle state */ state = !state;
}
/* timer 1 compare A interrupt service function */ ISR(TIMER1_COMPA_vect) {
/* do nothing if we are just processing a code in the main loop */
if (done)
return;
/* if some code has been received */
if (pos > 0) {
/* if pos is odd, one last 'off'-timing is missing, fill with zero */
if (pos % 2 == 1)
code[pos++] = 0;
/* signal main */
done = 1;
/* turn on third led */
PORTD |= _BV(PD6);
}
}
/* timer 2 compare A interrupt service function */ ISR(TIMER2_COMPA_vect) {
/* sample buttons every 10ms */ button_press |= button_sample();
}
int main(void) {
/* initialize uart */
uart_init();
uart_printf("rumpus ir analyzer\n");
/* configure led pins as outputs and turn leds off */ DDRC |= _BV(PC4); DDRD |= _BV(PD3) | _BV(PD6) | _BV(PD7); PORTC &= ~_BV(PC4); PORTD &= ~(_BV(PD3) | _BV(PD6) | _BV(PD7));
/* configure ir input pin, with pullup */ DDRC &= ~_BV(PC3); PORTC |= _BV(PC3);
/* configure button input pins, with pullup */ DDRC &= ~(_BV(PC0) | _BV(PC1) | _BV(PC2) | _BV(PC3)); PORTC |= _BV(PC0) | _BV(PC1) | _BV(PC2) | _BV(PC3);
/* configure ir send pin as output, set low */ DDRD |= _BV(PD5); PORTD &= ~_BV(PD5);
/* wait until pin is high (no ir carrier is detected) */ while(!(PINC & _BV(PC3)));
/* enable pin change interrupt 1 for ir input pin (PC3/PCINT11) */ PCMSK1 |= _BV(PCINT11); PCICR |= _BV(PCIE1);
/* configure timer1 with prescaler 64 and CTC for measuring ir timings */ TCCR1B = _BV(CS11) | _BV(CS10) | _BV(WGM12); /* configure timer action after 200ms: 20mhz/64/5 */ OCR1A = F_CPU/5/64; /* enable OCR1A interrupt */ TIMSK1 = _BV(OCIE1A);
/* configure timer 2 with prescaler 1024 and CTC
* for button sampling */
TCCR2A = _BV(WGM21);
TCCR2B = _BV(CS22) | _BV(CS21) | _BV(CS20);
/* configure compare event a to occur after 10ms and enable interrupt */
OCR2A = F_CPU/1024/100;
TIMSK2 = _BV(OCIE2A);
/* signal user availability by turning on led 1 */ PORTC |= _BV(PC4);
/* enable interrupts */ sei();
/* signal the user that the analyzer part has started by turning led 1 on */ PORTC |= _BV(PC3);
while(1) {
/* if a code has been received */
if (mode == MODE_DISPLAY && done) {
/* print code to serial uart */
uart_printf("complete code received, %u on-off-timings:\n", pos/2);
for (uint8_t i = 0; i < pos; i += 2) {
if (view == VIEW_VALUE_AND_TIME) {
uint32_t on, off;
/* compute timing in microseconds */
on = ((uint32_t)code[i]) * 64 / 20;
off = ((uint32_t)code[i+1]) * 64 / 20;
uart_printf(" %5lu us (%5u) on, %5lu us (%5u) off\n",
on, code[i],
off, code[i+1]);
} else if (view == VIEW_VALUE) {
uart_printf(" %5u on, %5u off\n",
code[i], code[i+1]);
} else if (view == VIEW_TIME) {
uint32_t on, off;
/* compute timing in microseconds */
on = ((uint32_t)code[i]) * 64 / 20;
off = ((uint32_t)code[i+1]) * 64 / 20;
uart_printf(" %5lu us on, %5lu us off\n",
on, off);
}
}
/* turn off second and third led */
PORTD &= ~(_BV(PD3) | _BV(PD6));
/* wait until pin is high (no ir carrier is detected) */
while(!(PINC & _BV(PC3)));
/* reset all global variables */
pos = 0;
state = 1;
done = 0;
}
if (mode == MODE_JAM) { jam(); }
if (done) { // code completely detected
/* reset all global variables */
pos = 0;
state = 1;
done = 0;
}
if (button_press) { /* first button toggles system mode */ if (button_press & 1) { mode++; if (mode > MODE_RECORD) mode = MODE_OFF;
if (mode == MODE_OFF) { uart_printf("ir analyzer switched off\n");
/* disable timer1 and pin change interrupts */ TIMSK1 &= ~_BV(OCIE1A); PCMSK1 &= ~_BV(PCINT11);
/* turn off led1 */ PORTC &= ~_BV(PC4);
} else if (mode == MODE_DISPLAY) { uart_printf("scan and display codes\n");
/* clear interrupt flags, enable timer1 and pin change interrupts */ TIFR1 = _BV(OCIE1A); TIMSK1 |= _BV(OCIE1A); PCMSK1 |= _BV(PCINT11);
/* turn on led1 */ PORTC |= _BV(PC4); } else if (mode == MODE_JAM) { /* clear interrupt flags, enable timer1 and pin change interrupts */ TIFR1 = _BV(OCIE1A); TIMSK1 |= _BV(OCIE1A); PCMSK1 |= _BV(PCINT11);
uart_printf("jamming mode active\n"); } else if (mode == MODE_RECORD) { uart_printf("record and replay a code\n"); } }
/* second button toggles view mode */
if (button_press & 2) {
view++;
if (view > VIEW_TIME)
view = VIEW_VALUE_AND_TIME;
if (view == VIEW_VALUE_AND_TIME) uart_printf("display timer value and time (in us)\n"); else if (view == VIEW_VALUE) uart_printf("display timer value\n"); else if (view == VIEW_TIME) uart_printf("display time (in us)\n"); }
if (button_press & 4) { static uint8_t pwm = 0;
if (!pwm) { ir_enable(PWM_FREQ); uart_printf("pwm on\n"); } else { ir_disable(); uart_printf("pwm off\n"); } pwm = !pwm; }
button_press = 0; } } }</source>
Eigener Chat
Hier wird die neue uart.c benutzt (die mit Senden und Empfangen). Leider funktioniert der Chat dann nicht mehr, vermutlich kommt der neue uart-Interrupt der wait-Funktion in die Query. Wenn man die alte uart.c benutzt kann man sich wunderbar über die 4 Taster unterhalten :) Hendi
<source lang="c">#include <avr/io.h>
- include <avr/interrupt.h>
- include <util/delay.h>
- include "uart.h"
/* constants */
- define MAX 160
/* 38khz: freq = F_CPU/(2*prescaler*frequency)
* 20mhz/(2*8*38khz) = ~33 * real frequency: 20mhz/(2*8*33) = ~37878Hz */
- define PWM_FREQ 33
/* global variables */
/* allocate 160*2 = 320 byte memory for storing a code,
* this means we can store 80 on/off sequence timings */
volatile uint16_t code[MAX]; /* current index in code[] (default: 0) */ volatile uint8_t pos = 0; /* current pin state (default: high == idle) */ volatile uint8_t state = 1; /* signal for the main application that a code has been received
* (default: 0) */
volatile uint8_t done = 0; /* signal button presses from interrupt to main */ volatile uint8_t button_press; /* current system mode */ enum {
MODE_OFF = 0, MODE_DISPLAY = 1, MODE_JAM = 2, MODE_RECORD = 3,
} mode = MODE_DISPLAY; /* current viewmode */ enum {
VIEW_VALUE_AND_TIME = 0, VIEW_VALUE = 1, VIEW_TIME = 2,
} view = VIEW_VALUE_AND_TIME;
/* call every 10 ms, for buttons at pins PC0-PC3 */ static uint8_t button_sample(void) {
/* initialize state, buttons are active low! */
static uint8_t btn_state = 15; //0b1111;
/* initialize old sample */
static uint8_t last_sample = 15; //0b1111;
/* read inputs */
uint8_t new_sample = PINC & 15; //0b1111;
/* mark bits which are sampled with the same value */
uint8_t same_sample = (last_sample ^ ~new_sample);
/* all bits set in same_sample now have been sampled with the same value
* at least two times, which means the button has settled */
/* compare the current button state with the most recent sampled value,
* but only for those bits which have stayed the same */
uint8_t state_different = btn_state ^ (new_sample & same_sample);
/* all bits set in state_different have been sampled at least two times
* with the same value, and this value is different from the current
* button state */
/* if a bit is set in state (means: button is not pressed) AND bit is set
* in state_different (means: input has settled and value is different
* from state) together means: button has been pressed recently */
uint8_t btn_press = btn_state & state_different;
/* toggle all bits for inputs which switched state */
btn_state ^= state_different;
/* store current sample for next time */
last_sample = new_sample;
/* if bit is set in btn_press, a button has been pressed
* (not released yet) */
return btn_press;
}
static void wait(uint32_t s) { uint32_t i; s /= 100; s *= 2.75; for (i = 0; i < s; i++) { _delay_us(100); } }
/* set up timer 0 to generate a carrier using pwm at freq on pin OC0B (PD5) */ static void ir_enable(uint8_t freq) {
/* timer 0: fast pwm mode, clear OC0B on match, prescaler 8 */ TCCR0A = _BV(WGM00) | _BV(COM0B1); TCCR0B = _BV(CS01) | _BV(WGM02); /* set frequency */ OCR0A = freq; /* set duty-cycle to 1/4 */ OCR0B = freq/4;
}
/* disable timer 0 and pwm generation */ static void ir_disable(void) {
TCCR0A = 0; TCCR0B = 0;
}
/* pin change interrupt 1 service function */
ISR(PCINT1_vect)
{
/* do nothing if we are just processing a code in the main loop,
* or no more space is available for a timer value */
if (done || pos == MAX)
return;
/* if this would be the first timing value ever recorded, and the
* state before was high (=idle), do not record the timing value
* and just reset the timer */
if (state && pos == 0) {
TCNT1 = 0;
/* else record the timing value */
} else {
/* store current timer value in code[]
* and reset the timer */
code[pos++] = TCNT1;
TCNT1 = 0;
}
/* toggle second led */
PORTD ^= _BV(PD3);
/* toggle state */
state = !state;
}
/* timer 1 compare A interrupt service function */ ISR(TIMER1_COMPA_vect) {
/* do nothing if we are just processing a code in the main loop */
if (done)
return;
/* if some code has been received */
if (pos > 0) {
/* if pos is odd, one last 'off'-timing is missing, fill with zero */
if (pos % 2 == 1)
code[pos++] = 0;
/* signal main */
done = 1;
/* turn on third led */
PORTD |= _BV(PD6);
}
}
/* timer 2 compare A interrupt service function */ ISR(TIMER2_COMPA_vect) {
/* sample buttons every 10ms */ button_press |= button_sample();
}
// NEC protocol, see http://www.sbprojects.com/knowledge/ir/nec.htm static void send1(void) { // uart_printf("1"); ir_enable(PWM_FREQ); wait(560); ir_disable(); wait(560); wait(560); }
static void send0(void) { // uart_printf("0"); ir_enable(PWM_FREQ); wait(560); ir_disable(); wait(560); }
static void send(uint8_t msg[]) { uint8_t sendcode;
while(!(PINC & _BV(PC3)));
// say hello ir_enable(PWM_FREQ); wait(9000); ir_disable(); wait(4500);
for (uint8_t z=0; z<100; z++) { if (msg[z] == '\r') { z=100; }
sendcode = msg[z];
// send data
for (uint8_t i=0; i<8; i++) {
if (sendcode & (1 << i)) {
send1();
} else {
send0();
}
}
}
// enable IR, so we know how long it was off ir_enable(PWM_FREQ); wait(560); ir_disable(); wait(560); }
static void receive(void) {
uint8_t rcv;
//uart_printf("-- %d --\n", pos); while(!(PINC & _BV(PC3)));
// transform time to ms
for (uint8_t i = 0; i < pos; i++) {
code[i] *= 64 / 20;
}
// receive hello
if (code[0] < 8500 || code[0] > 9500
|| code[1] < 4000 || code[1] > 5000
|| pos < 10
) {
// no nec hello found
uart_printf("no nec\n"); // return; }
// receive msg
for (uint8_t j=0; j<pos/8; j++) {
for (uint8_t i=0; i<8; i++) {
uart_printf("%d - ", code[16*j + 2*i + 2]); uart_printf("%d", code[16*j + 2*i + 3]); //uart_printf(" ----- ");
if (!(code[16*j + 2*i + 2] > 400 && code[16*j + 2*i + 2] < 800)) {
// bit doesn't start with ON
rcv = ' '; //uart_printf(" off FAIL (%d)\n", code[16*j + 2*i +2]);
i=8; continue; // go to next byte
}
if (code[16*j + 2*i + 3] > 400 && code[16*j + 2*i + 3] < 800) {
// bit is 0
rcv &= ~(1 << i);
} else if (code[16*j + 2*i + 3] > 900 && code[16*j + 2*i + 3] < 1300) {
// bit is 1
rcv |= 1 << i;
} else {
// not sure which value we have
rcv = ' '; //uart_printf(" FAIL (%d)\n", code[16*j + 2*i + 3]);
i=8; continue; // go to next byte
} }
uart_printf("%c", rcv); if (rcv == '\r') { j=pos/8; } uart_printf("\n");
}
}
int main(void) {
/* initialize uart */
uart_init();
uart_printf("rumpus ir chat\n");
/* configure led pins as outputs and turn leds off */
DDRC |= _BV(PC4);
DDRD |= _BV(PD3) | _BV(PD6) | _BV(PD7);
PORTC &= ~_BV(PC4);
PORTD &= ~(_BV(PD3) | _BV(PD6) | _BV(PD7));
/* configure ir input pin, with pullup */
DDRC &= ~_BV(PC3);
PORTC |= _BV(PC3);
/* configure button input pins, with pullup */
DDRC &= ~(_BV(PC0) | _BV(PC1) | _BV(PC2) | _BV(PC3));
PORTC |= _BV(PC0) | _BV(PC1) | _BV(PC2) | _BV(PC3);
/* configure ir send pin as output, set low */
DDRD |= _BV(PD5);
PORTD &= ~_BV(PD5);
/* wait until pin is high (no ir carrier is detected) */
while(!(PINC & _BV(PC3)));
/* enable pin change interrupt 1 for ir input pin (PC3/PCINT11) */
PCMSK1 |= _BV(PCINT11);
PCICR |= _BV(PCIE1);
/* configure timer1 with prescaler 64 and CTC for measuring ir timings */
TCCR1B = _BV(CS11) | _BV(CS10) | _BV(WGM12);
/* configure timer action after 200ms: 20mhz/64/5 */
OCR1A = F_CPU/5/64;
/* enable OCR1A interrupt */
TIMSK1 = _BV(OCIE1A);
/* configure timer 2 with prescaler 1024 and CTC
* for button sampling */
TCCR2A = _BV(WGM21);
TCCR2B = _BV(CS22) | _BV(CS21) | _BV(CS20);
/* configure compare event a to occur after 10ms and enable interrupt */
OCR2A = F_CPU/1024/100;
TIMSK2 = _BV(OCIE2A);
/* signal user availability by turning on led 1 */
PORTC |= _BV(PC4);
/* enable interrupts */
sei();
/* signal the user that the analyzer part has started by turning led 1 on */
PORTC |= _BV(PC3);
while(1) {
/* if a code has been received */
if (done) {
receive();
uart_printf("\n");
/* turn off second and third led */
PORTD &= ~(_BV(PD3) | _BV(PD6));
/* wait until pin is high (no ir carrier is detected) */
while(!(PINC & _BV(PC3)));
/* reset all global variables */
pos = 0;
state = 1;
done = 0;
}
if (uart_done == 1) {
send(uart_input); uart_len = 0; uart_done = 0; }
if (button_press) { /* first button toggles system mode */ uint8_t msg[7] = "Hallo!\r"; // SENDE if (button_press & (1 << 0)) { send(msg); } else if (button_press & (1 << 1)) { send(("Gruppe 1\r")); // 0b101 } else if (button_press & (1 << 2)) { send("1234567890\r"); // 0b10001 } else if (button_press & (1 << 3)) { send("XY\r"); }
button_press = 0;
}
}
}
</source>
